How To Repair Corner Cabinet Lazy Susan

Download Article

Adjusting misaligned Lazy Susan units might seem intimidating, but the most common corrections you'll need to make can exist done at home using standard tools. Fix rotation problems by adjusting the heart shaft or bottom shelf position. Remedy misaligned doors by correcting the door position from within the overall unit of measurement.

i
Pinpoint where rotation problems are occurring. When a Lazy Susan becomes stiff and difficult to rotate, the problem is usually caused by either the heart shaft or the position of its bottom shelf. Lightly spin the Susan and notation where information technology locks upwards, has difficulty turning, or has poor clearance.^[1]
- If the center movable shelf begins to bind, it will forestall costless rotation. In this state of affairs, yous'll need to loosen this shelf.
- If the circular shelves slip down the centre shaft, the bottom shelf can begin to drag, making information technology difficult to plough. You will need to adjust the meridian of this shelf to gear up the problem.
2
Locate the locking bolt to adjust the centre shaft. Look at the elevation of the eye shaft. At that place should be ane large bolt locking the exterior shaft to a metallic sleeve positioned within the shaft. This is the locking commodities for the shaft.^[ii]
- This commodities holds the heart shaft in place and maintains the length of the shaft. Sometimes backlog pressure from this commodities tin can cause the shaft to bind.
- On some models, the locking bolt might be located at the bottom of the Susan, withal, in most cases, it will plant near the elevation.
Advertizing
3
Loosen the commodities. If anything is inside your Lazy Susan, empty it and then you accept more than space to work. Using a wrench or ratchet, loosen the commodities by turning it one-quarter of a full rotation counterclockwise. At kickoff, the bolt may require some elbow grease to break loose.
- Merely loosen the bolt enough to manipulate the hardware within the heart shaft. On some models, this might require more than or less than i-quarter rotation.
- Mostly, it's ameliorate to loosen the commodities in small increments. This will forbid you from loosening it too much, which could event in the alignment of the Susan beingness thrown off.
iv
Move the adjusting rod. Now that the bolt is loose, yous'll be able to adjust the center shaft. Slide the metallic adjusting sleeve the commodities was holding in place no more than i inch (2.5 cm) to provide improve clearance between the center shaft and acme of the cabinet.^[3]
- Piece of work in small increments when adjusting the center shaft. Large adjustments could cause the Lazy Susan to topple over.
5

Tighten the bolt to end adjusting the center shaft. Use your wrench or ratchet to carefully refasten the locking bolt in place. Practice not over-tighten the bolt. It should be looser than information technology was initially, but nevertheless tight enough to concur the adjusting rod in identify.^[4]
vi
Locate the locking screws to suit the shelf position. Nigh Lazy Susans should accept two or more locking screws located at the center of each shelf. These screws agree the shelves to the middle shaft.
- When all of the shelves are held together past the front decorative console, you volition need to adjust the entire shelf organization. In this example, there may non exist screws located at the height of each shelf.
- If the shelves must be adapted separately, you'll just demand to work with the bottom shelf. Locate the locking screws in the bottom shelf only.
7
Loosen the screws. Loosen the locking screws using a Phillips-caput screwdriver or similar tool. Hold the screwdriver then its head meets the fastener direct on. Apply firm pressure down on the screw while turning counterclockwise to prevent stripping fastener hardware.^[5]
- Screws can exist left in their holes in one case they have been unattached from the center shaft. However, you may want to prepare loosened screws off to the side to prevent any from getting lost.
eight
Heighten the shelves to finish adjusting shelf position. Advisedly elevator the lesser shelf or unabridged shelf system until there is roughly half an inch (i.25 cm) of space between the bottom shelf and the lesser of the cabinet.
- The shelves may resist this aligning and begin binding on the center shaft. Maneuver shelves until they are level and at a suitable elevation.
- Under no circumstances should yous lubricate the center shaft. Doing so could preclude the screws from holding their position.
ix
Tighten the screws. Hold the shelf in identify with i paw and use your free hand to tighten the locking screws dorsum in place with a screwdriver. Take care not to let the shelf slip as you reattach fasteners, every bit this could crusade it to become uneven or binding.^[6]
- Brand the screws as tight as possible without stripping whatsoever of the hardware. The shelves must be stationary and secure to foreclose this kind of misalignment.
Advertizing

i
Locate where there are door problems. Door problems are usually easier to identify than rotation problems. The door of the unit may shut unevenly or it may not accept sufficient clearance at the top, bottom, or sides of the chiffonier.
- If the door does not close completely, or if it closes unevenly, you'll need to adjust the doors until they are centered correctly within the frame.
- When the acme or bottom clearance is insufficient, you'll discover the gaps at both sides of the door will exist diff.
- When the side clearance is insufficient, the door volition announced kleptomaniacal. Additionally, the gaps around it will but diff.
ii
Loosen the neckband screw when doors close unevenly. Open the door and locate the collar at the top of the unit. For many models, this function will be made of white plastic. Utilize a Phillips-head screwdriver to loosen the screw on this neckband.
- Loosen the screw by ane total counterclockwise rotation. Fifty-fifty loosened, the screw should remain in its position in the collar.
three
Rotate the shelf unit and door counterclockwise. Using both hands, carefully rotate the unabridged shelf unit and door in a counterclockwise management. Continue until the collar hits the take hold of latch located at the dorsum of the ceiling bracket.^[seven]
- Plough the Lazy Susan slowly. Listen for a slight click. This is a signal that yous've reached the catch latch.
- In one case y'all hit the catch latch, the collar should be properly aligned with the spring. You should experience a slight resistance to additional counterclockwise turning.
iv
Rotate the door. Gradually rotate the door in a clockwise direction until it reaches the exact eye-front end. If possible, accept a step back and check the alignment from a distance. Make sure the door is precisely in place before moving on.
- The plastic collar should remain stock-still in place equally you rotate the door, and so it may be difficult to step away. Have a friend or family member assist yous evaluate the door position, in these cases.
- If you accidentally rotate by the centre-front position, continue rotating the door in a clockwise direction. Do non rotate information technology counterclockwise until after you end setting it.
five
Turn the entire associates. Carefully and slowly rotate the unabridged assembly in a counterclockwise direction. Continue turning the assembly until the collar screw faces you. The door and collar should maintain their alignment as y'all plow the assembly.^[8]
- It may help you to maintain the position of the collar and door past marking their correct positions with a piece of painter's record, masking record, or something similar.
6
Tighten the screw to finish adjusting uneven doors. Tighten the collar screw dorsum into its original position. The door should now be properly aligned and stock-still into identify. Give the Lazy Susan a few spins to cheque that everything works correctly, and your door aligning is finished.^[9]
- To forestall the neckband from twisting out of place while it'southward fastened, you may demand to hold it in place equally the screw is tightened.
Advertisement

i
Remove the retainer clip to improve top and bottom clearance. Locate the plastic retainer clip at the bottom of the center shaft. Firmly grasp the clip between your fingers, open information technology, and pull information technology out. Under the prune should be a cut-out portion of the shaft with a thumbscrew adjustment wheel.
- The cabinet will need to be completely empty when you brand this aligning. Practice non try to complete the procedure when the shelves are loaded, especially if they are heavily loaded.
2
Turn the adjustment bike. Use your fingers to turn the thumbscrew aligning wheel in the cut-out portion of the center shaft. Rotate the wheel clockwise to raise the door and counterclockwise to lower the door.
- By and large you tin can look that for each full rotation of the screw the height will be adapted by about 1/32 in (0.eight mm).
- You may need to use gentle pressure to the underside of the bottom shelf to help the adjustment if you are attempting to raise the door.^[10]
3
Supplant the retainer clip to complete the top and lesser adjustment. After adjusting the door to the proper tiptop, return the retainer clip to its original position at the lesser of the pole. The clip should fasten back into identify firmly.^[xi]
- It'due south a good idea to tighten all of the adjustment screws attached to the center shaft, shelves, and door later setting the superlative. Doing this could foreclose the door from falling out of alignment again.
4
Outline the summit and bottom brackets when side clearance is bereft. Using an erasable pencil, lightly outline the current position of the top and bottom brackets. If lighting is too poor inside the chiffonier to make these marks easily, use a flashlight or electric lantern.
- Doing this will give y'all a reference bespeak to piece of work from equally you lot make the adjustment. Pencil marks can be erased one time yous complete the process.
five
Realign the pivot pole from the top. Use a screwdriver to remove the setscrews and loosen the star washers property the pin housing in place on both sides of the pivot pole. Adjust the pivot housing and pin pole until both are centered and aligned.^[12]
- When the star washers are in place merely before fastening the setscrews, take a stride back and expect over your Lazy Susan. If the side clearance is still uneven, remove the washers and readjust the pivot.
- Use your outline to guide your adjustments. For example, if the left side is low, yous'll likely need to move the pivot pole and housing to the right.
half-dozen
Refasten the pivot housing. One time you tighten the star washers, you'll be ready to return the setscrews to their original position. When the screws are in identify, cheque the side clearance of the Lazy Susan again to make sure that it wasn't contradistinct as you lot refastened its hardware.^[thirteen]
- This adjustment may take care of your side clearance problem. If the lower half of your Susan appears to be misaligned, y'all'll take to adjust the pivot base in improver to its top.
7
Realign the pin base when necessary. Open the door wide plenty to expose the bottom bracket on either side of the Susan. Loosen this bracket by removing the fastening setscrew and star washer with a screwdriver. Now you can realign the pivot cam (metal arm) base so that it'due south centered.^[14]
- You'll accept to repeat this process on the opposite side of the Lazy Susan where you'll discover an identical bracket/pin cam base.
- Work on brackets one at a fourth dimension. Subsequently you've taken apart, realigned, and refastened the first subclass, move on to the adjacent 1.
- When properly centered, the pin cam bases of both sides should be aligned with regard to the center pole.
viii
Refasten the bracket. Be careful when refastening; if you jostle the pivot cam, it could be knocked out of alignment. Replace the star washers and reattach the setscrews for the bracket. When attached, similarly adjust the contrary side bottom subclass/pin cam base.
- Verify that the position did not become contradistinct while y'all were returning these pieces to their original positions by stepping back and evaluating the evenness of the side clearance.
ix
Bank check the door to complete your side clearance adjustment. Sometimes these alignments (especially those made to pivots) can crave several attempts earlier they are resolved. Double check door alignment after completing the top and bottom adjustments, especially.^[15]
- If the side clearance is still diff, you will demand to readjust the top pivot pole and/or lesser pin cams.
Ad

Add New Question

Question

How exercise I tighten a Lazy Susan that keeps turning around and effectually? Information technology won't lock in place.

There is a plastic clasp at the top of the Lazy Susan. You will see a notch in it that should catch then that information technology holds the unit in place. Normally, the older units will evidence the plastic to be worn. Simply replace the plastic piece, and it should realign and shut properly.
Question

What shelf do I put the heavy items on, top or bottom?

Putting the heavy items like canned goods on top will increase the chances of the shelf breaking, so put heavy stuff not the bottom instead. The top shelf is better for boxes of pasta and bags of rice.
Question

How do I gear up set screws that won't tighten?

If the screws for your Lazy Susan don't tighten, the fasteners or the attaching hardware may be stripped. This means that damage has been washed to the part of the hardware intended to grip the fastener (like the grooves of a screw). Replace stripped hardware and endeavor again.
Question

How can I accommodate a bottom corner cabinet lazy susan that has the cabinet door attached?

If you take the one with a cam at the top of the center pole and a screw with a spring, then adjusting the screw on the side that has a spring on it will adjust how the outer surface of the lazy susan "door" aligns with the rest of the cabinets. Don't be agape to tighten all the way or loosen every bit far every bit possible. From what I tin tell, the screw will not come out. I turned the screw in and idea I counted the turns. Then backed it out once again the same amount of turns and all all of a sudden the door was more than than an inch out of alignment. I had to back it out a lot further to reset the alignment.
Question

How practise I fix a lazy Susan if the shelf adjuster fell and took the shelf with information technology? There is non plenty room to adjust information technology and the flange is crooked.

If the shelf suit roughshod and knocked a shelf out, damaging the shelf flange, yous may need to completely disassemble the shelf, supersede the damaged hardware (inexpensive flanges can be bought at most hardware stores), and then reinstall the Lazy Susan.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Thanks for submitting a tip for review!

Things You lot'll Need

Eraser
Flashlight (or electric lantern for low-cal; optional)
Pencil
Phillips-head screwdriver
Standard screwdriver
Wrench (or ratchet set)

About This Commodity

Article Summary X

If y'all're having bug with your Lazy Susan, you should be able to adjust it using standard tools. Before y'all make whatsoever adjustments, empty the cupboard so you lot have space to work. If the shelves are stiff when you plow them, loosen the locking bolt at the top of the center shaft with a wrench or ratchet, so move the adjusting rod an inch, and tighten the bolt. To fix the shelf elevation, unscrew the locking screws on the central shaft that hold each shelf, arrange the elevation, then tighten the screws once again. If the doors are misaligned, use a Philips-head screwdriver to loosen the screw at the peak of the doors, rotate the shelf unit and door counterclockwise until the superlative hits the latch, then rotate the door clockwise until information technology reaches the center. For more tips, including how to arrange the clearance inside your Lazy Susan, read on!

Did this summary help y'all?

Thanks to all authors for creating a page that has been read 166,754 times.